Jean Pierre.
Thanks for your response. I am using an old channel master LNB which has a DRO LO I think it is not good enough for 3cm digital and when possible I will replace it.
With regard to my MiniTioune running in Vista I have today tried your original unmodified ini file and I still get the PID error screens at loading. Below I have copied my modified in file for you to check.... 73 de Denis G3UVR
;=====================================================================
[Language]
;=====================================================================
Langue=English
;=====================================================================
[TSbuffer]
;=====================================================================
;
; number of 1316 bytes buffers used for TS transfert --- use a value 2 to 30
Totalbuffers=6
;=====================================================================
;=====================================================================
[WebMonitoring]
;=====================================================================
;Station Idendificator: write a number 1 to N suiting number of Tutioune Station you have - for distinguish them
Station_ID=1
; OM_ID:give only your OM you call sign, maximum 7 letters accepted
; this call sign must be the same you have used for regsitering to vivadatv.org
; use same password as you use for vivadatv forum/ utilisez le même mot de passe que pour le forum vivadatv
OM_ID=G3UVR
ForumPassword =??????????????
Locator=IO83KH
Ville=11km SW Liverpool
DirectionAntenne=Yagi
; Gain / write 2 digits
GainAntennedB=16
GainPreamplidB=20
;=====================================================================
; Symbol Rate buttons
[SRPresetButtons]
;=====================================================================
; Value in kSymbols
;
SR1Value=4167
SR1Text=SR4167
SR2Value=4000
SR2Text=SR4000
SR3Value=2000
SR3Text=SR2000
SR4Value=1000
SR4Text=SR1000
SR5Value=333
SR5Text=SR333
;=====================================================================
; Frequency for preset buttons ==> 8 DIGITS!
[FreqPresetButtons]
;=====================================================================
; Value in khz >>> 8 DIGITS
Freq1Value=01319000
Offset1Value=-00000000
Freq1Text=1319 MHz
;.......................................
Freq2Value=01316000
Offset2Value =00000000
Freq2Text=1316 MHz
;.......................................
Freq3Value=01285000
Offset3Value =-00000000
Freq3Text=1285 MHz
;.......................................
Freq4Value=02335000
Offset4Value =00000000
Freq4Text=2335 MHz
;.......................................
Freq5Value=10376000
; G3UVR LNB offset
Offset5Value =-09117000
Freq5Text=10,376 MHz
;Freq5Value=11597000
; Standard Satellite LNB offset
;Offset5Value =-09750000
;Freq5Text=11597MHz
;Freq5Value=00437000
; F1GE sup 2400
;Offset5Value =-02400230
;Freq4Text=437ge MHz
;Freq5Value=00437000
; DG0VE converter offset
;Offset5Value =+00902000
;Freq5Text=437 MHz
;=====================================================================
; list of FEC allowed to scan 0=No 1 = Yes
[FecAcceptedValues]
;=====================================================================
Fec12=1
FEc35=1
Fec23=1
Fec34=1
Fec45=0
Fec56=1
Fec67=0
Fec78=1
Fec89=1
Fec910=0
;=====================================================================
; UDP address
[UDP]
;=====================================================================
;AddrUDP=230.0.0.1
;AddrUDP=127.0.0.1
;Port=1234
; mettre ici l'IP que vous utilisez pour faire l'envoi : localIP
; cela sert dans le cas ou vous avez plusieurs réseaux locaux comme chez moi
; un réseau wifi pour Internet et un réseau local en ethernet
; NE METTRE QUE SI VOUS AVEZ BIEN VERIFIE VOTRE IP DE VOTRE CONNEXION RESEAU
;LocalIP=192.168.1.11
;=====================================================================
; PID
[PIDs]
;=====================================================================
; autoPID when starting software = yes or no
AutoPID=yes
;.......................................
; number of stations -----> MAXIMUM 6
NbStationsIni=6
Station1=F6DZP-Mpeg2
PIDVideo1=1001
PIDaudio1=1002
Codec1=Mpeg2
;.......................................
Station2=F6DZP-H264
PIDVideo2=1001
PIDaudio2=1002
Codec2=H264
;.......................................
Station3=HDlowSR
PIDVideo3=4113
PIDaudio3=4352
Codec3=H264
;.......................................
Station4=France24
PIDvideo4=605
PIDaudio4=625
Codec4=Mpeg2
;.......................................
Station5=QRZ DX
PIDVideo5=33
PIDaudio5=49
Codec5=Mpeg2
Station6=RaspberryPi
PIDVideo6=1001
PIDaudio6=1000
Codec6=H264
;=====================================================================
;scan parameters
[scan]
;=====================================================================
; range/course affect the nbr of KHz the derotator will explore for locking
;value is between 1 and 13
range1=12
; timer1 unit is 1 sec, timing between each scanning start value 2 to 16 sec
timer1=8
; range2 = afterlock, value : 0 to 12 0=freeze on freq
range2=10
; timer2 unit is 1/2 sec so value : 2 to 16 ==> 1 to 8 sec
timer2=6
;PLL corrector Automode : 0=no 1=yes
pllcorrection=0
; default scan mode: wide or narrow
scanmode=wide
; SR search mode A ou/or B
searchmode=B
;=====================================================================
; Here you can preset buttons
[buttons]
;=====================================================================
; ISSmode
;utilisé pour suivre l'egffet Doppler et corriger le bug HAmTV oui/yes(1) Non/No : (0)
;used for ISS doppler effect and HamTV bug correction Non/No : (0) oui/yes(1)
; /force also PID values to 256 and 257
issmode=0
;.......................................
; Dsave_Switch 0=OFF 1=ON
dsave_switch=0
;.......................................
; WebMonitor 0=OFF 1=ON
web_switch=0
;.......................................
;UDP_switch 0=OFF 1=ON
udp_switch=0
;.......................................
;Record_switch 0=OFF 1=ON
record_switch=0
;.......................................
;22 kHz 0=OFF 1=ON 2= ON when TS OK
22kHz_switch=0
;..............................................
;TSerrorBit_switch 0=ON 1 = OFF
TSerrorBit_switch = 0
;.......................................
;Expert_switch 0=OFF 1=ON
Expert_switch=1
;.......................................
;LowSR_switch 0=OFF 1=ON //ne peut être ON que si SR1Value<6500 kS/s // can be ON only if SR1Value<6500 kS/s
; //ne peut être OFF que si SR1Value>=300 kS/s // can be OFF only if SR1Value>=300 kS/s
LowSR_switch=1
;.......................................
;BBgainAuto_switch 1= auto_ON ..,-2,0, 2, 4, 6, 8 ... = auto_OFF
;value accepted for Sharp/samsung NIM: 0,2,4,6,8,10,12,14,16 for Eardatek NIM: -10,-8,-6,-4,-2,0,2,4,6,8,10,12,14
BBgainAuto_switch=-10